HappyModel Mobula7 1S HD Micro FPV 75mm Analog Whoop Drone

  • $180.00
  • Save $9

$180.00 $189.00
FrSky (SPI D8/D16)
FrSky (SPI D8/D16)

$170.00 $189.00

HappyModel Mobula7 1S HD Micro FPV 75mm Analog Whoop Drone 1080 DVR RunCam Split3 Lite BNF FrSky ELRS

Mobula7 1S HD version is a light and efficiency 75mm brushless whoop which provide 1080P HD video record function. A highly integrated AIO Flight Controller, supports ESC with a maximum current output of 12A. We added blackbox for this 1s 75mm HD recorder whoop. Now it could support gyroflow. Although the external blackbox is not install perfectly and insert SD card is not friendly to most of the people, however we still think it's really excited for this small whoop could record a video with gyroflow steady and keep safe flying.



  • X12 5-IN-1 AIO flight controller
  • VTX Power up to 400mw
  • ELRS V2.0 Support
  • NEW RS0802 KV20000 motors
  • 1080P HD Video record
  • Blackbox Ready support GYROFLOW
  • Smooth and powerful
  • Compatible for 1S Lipo/LIHV
  • Recommend 1S 450mah/550mah/650mah batteries (Not include)



  • Brand Name: Happymodel
  • Item Name: Mobula7 1S HD 75mm Micro FPV whoop drone
  • Wheelbase: 75mm
  • Size: 99mm*99mm*45.5mm
  • Weight: 33g


Receiver option:

  • SPI 2.4GHz ELRS V2.0
  • SPI Frsky D8/D16


Package includes:

  • 1x Mobula7 1S 75mm whoop Drone Frame (Mobula7 v4 frame)
  • 1x X12 ELRS V2.0 flight controller built-in SPI ELRS 2.4G receiver or X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver
  • 1x External Blackbox Module support gyroflow
  • 4x RS0802 KV20000 brushless motor
  • 1x Gemfan 1610-2 bi-blade propellers(4cw+4ccw)
  • 1x Runcam Split3-Lite Camera+1080P DVR
  • 1x 1S series balance charging board
  • 1x Propeller disassemble tool


Spare parts specifications:


  • Mode: RS0802 KV20000
  • Configu-ration:9N12P
  • Stator Diamter:8mm
  • Stator Length:2mm
  • Shaft Diameter:Φ1.5mm
  • Motor Dimension(Dia.*Len):Φ10.5mm*13.5mm
  • Weight(g):2.0g
  • No.of Cells(Lipo):1S only


  • Weight:0.24g
  • Material:PC
  • Pitch:1 inch
  • Props Dia:40mm
  • Center Thickness:5mm
  • Center Hole Dia:1.5mm

Flight Controller

  • X12 ELRS V2.0 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280
  • X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR
  • MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
  • Sensor: ICM20689(SPI connection)
  • Mount hole size: 25.5mm*25.5mm
  • Power supply: 1S battery input (DC 2.9V-4.35V)
  • Built-in 12A(each) Blheli_S 4in1 ESC
  • Built-in Betaflight OSD(SPI Control)
  • Built-in 5.8G OpenVTX 0mw~400mw
  • Built-in ExpressLRS 2.4G,Frsky D8/D16
  • Built-in voltage detection
  • Built-in current sensor

Onboard 4in1 ESC

  • Power supply: 1S LiPo/LiPo HV
  • Current: 12A continuous peak 15A (3 seconds)
  • Support BLHeliSuite programmable
  • Factory firmware: Z_H_30_REV16_7.HEX
  • Default protocol: DSHOT300
  • Support Bluejay firmware
  • When use Blujay firmware with 48khz, should set startup power to 1100/1200

Onboard SPI ExpressLRS 2.4GHz Receiver

  • Packet Rate option: 50Hz/150Hz/250Hz/500Hz
  • ExpressLRS Firmware version: V2.0
  • RF Frequency: 2.4GHz
  • Antenna : Enameled copper wire length 30mm
  • Telemetry output Power: <12dBm
  • Receiver protocol:  SPI ExpressLRS
  • Compatible with ExpressLRS V2.0 TX Module
  • Couldn’t flash separately ExpressLRS firmware

Onboard Frsky SPI D8/D16 receiver Version

  • SPI BUS receiver Frsky D8 D16 compatible
  • Could working on FRSKY D8/D16/D16 LBT/REDPINE/SFHSS protocol
  • Channels: 8ch or 16CH
  • No ground interference ( Transmitter and receiver 1 m from the ground): 200meter
  • Failsafe support

Onboard 5.8g OPENVTX

  • Firmware version: OPENVTX
  • Smartaudio v2.1
  • PIT Mode support
  • RCE Mode support
  • Channels:48ch
  • Transmitting Power: 0/RCE/25mw/100mw/400mw
  • Power supply: DC 5V
  • Current (5v): <650ma (400mw)

Runcam Split3-Lite

  • Model: RunCam Split3-Lite
  • Field of View(FOV):Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
  • Video Resolution:1080@60fps/1080@50fps/1080@30fps/720@60fps
  • Video File Format: MOV
  • Image Resolution:2 MP
  • TV Mode: NTSC (720*480)/PAL (720*576) Switchable
  • Interface: JST 1.25mm / UART and SH 1.0mm
  • Max Micro SD Card Supported  64G(need Class 6 or above, recommend Class 10/UHS-I/UHS-II/UHS-III)
  • Hole Distance of Installation: 25.5*25.5mm
  • PCB Size: 29*29mm
  • Lens Module Size: 14*14mm
  • Lens Specs: M9
  • Power Input: DC 5-20V(Non-direct power supply from battery. Powered directly with battery will generate surges and burn the camera.)
  • Working Current: 450mA @5V

External Blackbox

  • Size:18*15.5*4.5
  • With Built-in Voltage booster module
  • Weight:1.5gram
  • SD Card support max to 32GB
  • SD Card need to use FAT32 Format

Notes: Need to careful to insert the TF SD Card , and don't pull it out while install the battery.