HappyModel Mobula8 HD O3 DJI Digital 2S Whoop 85mm FPV Racing Drone

  • $365.00
  • Save $76

HappyModel Mobula8 HD O3 DJI Digital 2S Whoop 85mm FPV Racing Drone BNF ELRS


The New Mobula8 Digital HD Micro FPV whoop comes with a new flight controller which is specific for Digital HD CINEWHOOP. Built in UART ExpressLRS receiver and 12A 4IN1 BLheli_S ESC.

The same Brushless motor and Gemfan 2023 propeller like the Mobula8 Analog version. Comes With DJI O3, Walksnail avatar and HDZERO VTX option. Smooth flight and High definition video transmission would bring us exited FPV experience.

Notice: According to DJI’s warranty policy, if there is a problem with the DJI O3 Air unit installed on the BNF Drone, it needs to be sent back to China mainland for warranty, please noticed.


  • Digital HD FPV experience
  • New CrazyF405 ELRS HD flight controller
  • Powerful and Smooth
  • UART ExpressLRS receiver
  • Built-in blackbox for Gyroflow and PID Tune

Mode: EX1103 11000KV
Stator Diamter:11mm
Stator Length:3mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.*Len):Φ13.5mm*15.5mm
No.of Cells(Lipo):1-2S
Material: PC
Props Dia:52.17mm
Center Thickness:5mm
Center Hole Dia:1.5mm
Flight Controller
MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
GYRO Sensor: BMI270 (SPI connection)
Mount hole size: 25.5mm*25.5mm
Power supply: 1-2S battery input (DC 2.9V-8.7V)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Serial ExpressLRS 2.4G
Built-in BMP280 Barometer
Built-in 8MBp blackbox
Built-in voltage meter sensor , voltage meter scale 110
Built-in current meter sensor , current meter scale 470
Onboard 4in1 ESC
Power supply: 1-2S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Support BLHeli_S Bluejay firmware
Factory firmware: Bluejay ESC V0.19
Firmware target: Z-H-30
Default protocol: DSHOT300
When use 1s battery and high KV 0702/0802 motors, should set startup power to 1100/1200

Onboard UART

ExpressLRS 2.4GHz Receiver:

Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHz
Antenna: enameled copper wire 31mm length
Telemetry output Power: <12dBm
Default firmware version: ExpressLRS V3.0.1
Firmware target: HappyModel EP 2400 RX
Could update firmware via ExpressLRS configurator
DJI O3 Version VTX & Camera: DJI O3 Air Unit
Works with DJI FPV Goggles V2, DJI Goggles 2, and DJI FPV Remote Controller 2
Walksnail Version

Camera: Avatar lite camera

VTX: Avatar mini 1s module

HDZero Version HDZero Nano Lite Camera & HDZero Whoop Lite VTX
Lite Version NO VTX, NO Camera

Package includes:

  • 1x Mobula8 Frame x1
  • 1x CrazyF4HD ELRS flight controller firmware target: BETAFLIGHTF4
  • 4x EX1103 KV11000 brushless motor
  • 1x Gemfan Hurricane 2023 tri-blade propellers(4cw+4ccw)
  • 1x DJI O3 Air unit
  • 1x Canopy
  • 1x Screw driver